|
|
 |
|
220V Semi automatic PCB foot cutting machine |
|
|
The breadboard wipe cutting machine is mainly applied in
cutting the unwanted pin after the welding of parts of
apparatus and this machine is assembled by parts made
with exquisite craftwork. The key parts are dealt with
grinding , and the imported bearing assembled wipe
cutting machine grinding consistency is excellent, the
rotating speed of blade is fast and is very
efficient and convenient to operate with
little noise. The double lead rail is adjusted
synchronously , the height of wipe cutting is adjustable
and the outlook is attractive. "Continuous improvement,
lasting and efficient, clients first" is our quality
tenet, it is our honor to serve you.
|
|
Instruction
of adjusting |
1.Open
the package and read the instruction carefully and check
the accessories (refer to term 7 in the instruction)
2.Check the body of machine for any abnormal phenomena,
if so , contact the local agent as soon as possible
3.After conforming the good connection of the case
earth, plug in.
4.First adjust the double lead rail travel route
biggest, unscrew the gland bush screw(gland bush screw
is right-handed screw )with 8# inner hexagonal wrench
counterclockwise,take out the blade gland bush and clean
up both sides of tool apron, blade, gland bush with
clean and soft cloth. Then place gently the blade on the
base(surface up). Next ,place the blade gland bush on
the blade, screw down the gland bush screw with 8# inner
hexagonal wrench clockwise. When unloading the blade,
use the enclosed dismantled stick to fix the tool apron.
5. Rotate the adjusting hand wheel, adjust the width
between the lead rails, and place one wanted placode of
wipe cutting machine on the entrance and exit port
respectively. Rotate the hand wheel until the placode at
both ports slide properly in the lead rail.
6.Four sets(three screws per set)assembling screws that
are equipped on top of lead rail bland bush are used to
adjust the thickness of placode. During the adjusting
first unscrew three perch screws among them and put
placode inside and then adjust two lower order screws
besides until they fit and screw down the middle screw.
Operation are the same for four sets and adjust placode
to slide properly inside the lead rail
7.Adjusting of height of wipe cutting machine : screw
down lead rail retaining screw and adjust the big screw
cap until the distance between blade and lead rail meets
the requirement then screw down lead rail retaining
screw. When adjusting lower avoid any friction between
lead rail and blade for fear of damage to blade.
8. The height of wipe cutting of wipe cutting machine
was adjusted as 1.5mm when it leaves factory and the
thickness of textile board was adjusted as 1.2mm. When
adjusting is necessary please adjust according to method
mentioned above.
|
|
Features |
 |
Blade jitter small
Pin cutting leveling
|
|
The 3 hole blade gland uses the triangle positioning
principle, the blade is firmly fixed, not easy to loose, the
high speed running condition, the blade does not slip, the
operation is smooth, the cutting foot is accurate, the
safety factor is high.
|
 |
 |
The whole machine is steady, low noise and low jitter.
|
|
The feeding guide rail of the fine steel is of high
thickness, wear resistance, not easy to deform and prolong
the service life of the machine.
|
 |
 |
Line type cutting. |
|
Specifiction |
|
 |
 |
Notice: We
send a blade($350) as a gift. |
|
Operations |
|
1.
Place the welded breadboard on the adjusted wipe cutting machine and
insert the lead rail down the leading-in of lead rail.
2.Push dexter feed hand shank and push placode advance at constant
speed
3.Repeat step 1,2 and finish cutting the welded placode.
Notice: When the placode moves avoid moving too fast, and moving too
fast can directly shorten the use life of blade and even endanger
safety. |
|
Maintenance |
Wipe cutting machine
is the mechanic equipment of high accuracy and with high speed and
the constant maintenance prolongs its use life
1.The rotating part needs constant lubrication.
2.Clean up the cut pin
3.If the transmitting triangle strap is damaged, it needs immediate
replacement and the specification is (0-450)
4.The blade should not leave cutter head for too long, lubricate the
cutter head when necessary if it leaves for several days. |
|
Notice |
|
1.When the machine
is in operation avoid putting hands into the machine.
2. This machine must work in the state of good earth connection
3.Cut off the power when installing or dismantling blade or in case
of emergency
4.Cut off the power in sace of a blackout.
5.This machine should not be used in humid, flammable, corrosive,
dense bug dust-filled environment.
6. Non professional repairmen are not allowed to dismantle the cover
to repair it personally .
7.Do not open the cover when the machine rotates.
8.Operate the machine according to instruction strictly; otherwise
out factory takes no responsibility. |
|
Item Include(151005) |
- A set of 220V?Semi automatic PCB foot cutting machine
- A set of Blade
|
|
