|
LED SMT Reflow Oven T-960e 220V |
|
|
|
|
|
|
|
 |
|
Features |
1.This machine selects IR and hot air heating technology controlling,
equipped with special design wind wheel, speed stability and uniform
temperature, suit for uninterrupted soldering the LED and BGA
components.
2. This machine is equipped with the crawler-type and five temperature
zone heating systems, and each temperature zone uses independent PID
controlling and up-down heating type, can make the inside temperature
more accurate and well-proportioned, just take about 20 minutes can let
it heat up to the working temperature from the room temperature.
3. Intelligent temperature wave heating type, oversized capacity wave
selection, have eight temperature waves can satisfy various welding
technological requirements.
4. Use programmable technology, preset the temperature wave memory
storage function, can complete the whole welding process automatically
according to your presetting wave.
5. Adopt the thermocouple temperature measurement and add the
compensation circuit, make the temperature measurement more accurate,
the wave more perfect.
6. Use PID intelligent temperature control technology; make the
temperature control more accurately. Adopt the imported large current
solid-state relay non-contact output can effectively avoid the IC or
circuit board damage due to the rapid or uninterrupted warming up, make
the whole welding process more scientific safety.
7.Transmission system adopt imported frequency conversion motor, PID
closed-loop speed, equip with all the import 1:150 turbine speed
reducer, smooth operation, speed adjustable range 0-1600mm/min.
8. Adopt independent wheel structure and special stainless steel strut,
durable wear-resisting runs smoothly, speed precision can reach
±10mm/min.
9. Independent cooling zone, to ensure the PCB board of low temperature
when the required.
10. Friendly human-machine operation interface, perfect LCD display, no
need to connect with the PC, can watch the whole repairing process very
clearly.
11. Ergonomic design, practical and easily operated. Good build quality
but at the same time light weight and a small footprint allows the
T-960e to be easily bench positioned, transported or stored. |
|
Parameters |
|
|
The heating zone quantity |
upper3/down2 |
|
|
The length of the heating zone |
960mm |
|
The heating type |
IR and hot air heating |
|
The cooling zone quantity |
1 |
|
Maximum width of PCB board |
300MM |
|
The operation direction |
left→right |
|
Delivery options |
Net transmission＋chain transmission |
|
The speed of conveyer belt |
0-1600mm/min |
|
The power supply |
220V |
|
Average power
|
4.5KW |
|
Peak power |
8KW |
|
Heating up time |
Around 15mins |
|
Temperature control range |
Room temperature～350℃ |
|
Temperature control mode |
PID closed-loop control |
|
Temperature control accuracy |
±1℃ |
|
PCB temperature distribution deviation |
±2℃ |
|
Overall dimensions |
120cm*77cm*44cm |
|
Machine weight |
91.5kg |
|
Product display |
|
|
|
How to connect the wires |
|
L1、L2-Firewire PE- Earth wire
NOTE:Customers need to prepare at least six square millimeters of power
cables themselves. |
|
Characteristic |
|
|
1.Front-loadoperation
Outside-load operation panel avoids highlytemperature
in the panel to improve stability. |
|
2.eight waves can be preset and memory
a.Use programmable technology,preset the temperature
wavestorage,can complete the whole soldering process
automaticallyaccording to your preseting wave.
b.Easy operation,8 waves satisfy various soldering
technologicalrequirements,avoid to change temperature every time. |
 |
|
 |
3.LCD display intuitive
LCD display intuitive every data. |
|
4.PID temperature control system
PID temperature control system,temperaturesetting is
convenient,high precision oftemperature
control,lower-power,highlyproduction efficiency. |
 |
|
|
5.Heating insulation laver in tank for insulation
Heating insulation layer in tank for insulation to
keep temperaturestability of six zones. |
|
Equipment Installation |
|
Set up field |
1.Please do the work in the clean environment condition. 2. Do not put
the machine near the electromagnetism interfering resource.
3. Do not put the oven exits and entrances face towards to the fan and
the window |
|
Power supply |
Please use the correct voltage . Ensure the machine contacts the earth
well and requested professional electrician operation.
|
|
Adjust the reflow oven height |
By adjust the machine leg to adjust the height. The way is follow: use
industrial or alcohol gradienter to measure. Then adjust the machine leg
to adjust the dryer on all sides till it is completely horizontal.
|
|
Caution |
1. The working environment should be clean. So the welder quality is
good.
2. Do not use and store the machine out of door, high temperature and
humid condition.
3. During operation take care of the high temperature, avoid scald.
4. When overhaul the machine, please cut off the power supply to avoid
electric shock or cause short circuit.
5. If move the machine after overhaul, must check all the parts,
especially the net-belt position. Cannot make it be lock or fall off.
6. Ensure the machine is stable, not lean or instable. Adjust the leg
under the machine to keep the transmission horizontal. Or the PCB will
shift in the transmit process.
7. Do not put too big and big absorbed heat components into the oven
avoiding damage the net-net and affect the temperature.
8. Put lubricating oil into the transmission chain every 7 days.
9. Do not put the inflammable and explosive dangerous goods near the
reflow oven.
10. Do not reach hands into the reflow oven when the machine is in
normal working condition. |
|
Daily Maintenance |
1. Keep the electrical control cabinet clean.
2. Check the fan shaft sleeve is in good condition.
3. Check the fan and the electro-motor have abnormal sound.
4. Be sure the fan does work flexibly.
5. Check the air hole if there are abnormal materials.
6. Check the transmission net-belt is in good condition.
7. Check the electrical chest and electrical equipment have abnormal
sound.
8. Check the transmission part if it is in good condition and has
abnormal sound.
9. Before turn on the machine, please check the working voltage if it is
in the safe voltage and if it is stable. Ensure all the parts can work
safely and normally. At the same time, when turn on the machine, check
the parameters are the same to the last time turn off. When turn off the
machine, do not let the transmission belt in the hot area, please turn
off the temperature and when cool down well and stop the transmission
belt.
10. Lubricate the driving rolls. Put lubricating oil every two months.
11. The motor works in high temperature for long time, please put
lubricating oil twice a week or more, ensure the motor can work
normally.
12. Clean the residual goods on the fan blade and motor timely. Or the
circuit ages will lead to short circuit and damage the fan.
13. Be sure the machine contacts the earth when use five-wire system.
|
|
Item Number: 022606 |
|
|
You can make
order with no worry.
Any concerns just feel free to let us know, we'll reply in 24 hours in
normal condition.
Handling Time: Shipping is usually made in 1-3 business days after
payments cleared. Orders are processed from Monday-Friday; Not on the
weekends & public holidays.
Warranty: 6 months' warranty for the machines, not for the consumables.
We stand behind our products all the item, so even if your warranty
period has expired, you can still seek for service or technical support
from us with low cost. |
